FIBRE GLASS-EVERCOAT CO INC -- FORMULA 27  -- 8030-00N017477
<pre>=====================  Product Identification  =====================

Product ID:FORMULA 27
MSDS Date:08/09/1988
FSC:8030
NIIN:00N017477
=== Responsible Party ===
Company Name:FIBRE GLASS-EVERCOAT CO INC
Address:6600 CORNELL ROAD
City:CINCINNATI
State:OH
ZIP:45242-2033
Country:US
Info Phone Num:513-489-7600
Emergency Phone Num:800-543-4530
CAGE:18731
=== Contractor Identification ===
Company Name:FIBRE GLASS-EVERCOAT CO INC
Address:6600 CORNELL ROAD
Box:City:CINCINNATI
State:OH
ZIP:45242
Country:US
Phone:513-489-7600
CAGE:18731

=============  Composition/Information on Ingredients  =============

Ingred Name:STYRENE
CAS:100-42-5
RTECS #:WL3675000
Fraction by Wt: <20%
OSHA PEL:100 PPM
ACGIH TLV:S,50PPM/100STEL;9293
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS

Ingred Name:TALC (POWDER), CONTAINING NO ASBESTOS FIBERS; (TALC)
CAS:14807-96-6
RTECS #:WW2710000
Fraction by Wt: <50%
OSHA PEL:2 MG/M3 (RDUST)
ACGIH TLV:2 MG/M3 (RDUST)

Ingred Name:UNSATURATED POLYESTER RESIN
Fraction by Wt: <40%

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:YES    IARC:NO	 OSHA:NO
Health Hazards Acute and Chronic:ACUTE: SKIN: PRLNGD/FREQUENT CONTACT
    MAY CAUSE DEFAT, DRYNESS W/IRRIT, & POSS DERM. STYRENE MAY BE
    ABSORBED THROUGH SKIN IN TOXIC AMTS. EYES: MAY CAUSE TEARING/IRRIT.
    INHAL: VAPORS MAY CAUSE NOSE,THRO AT & RESP TRACT IRRIT. HIGH CONC
    MAY CAUSE HDCH & NAUSEA. INGEST:MAY CAUSE GI DISTURBANCE, PAIN &
    (EFTS OF OVEREXP)
Explanation of Carcinogenicity:STYRENE:GROUP 2B (IARC).
Effects of Overexposure:HLTH HAZ:DISCOMFORT. CHRONIC: REPEATED
    INHALATION OF HIGH CONCENTRATIONS MAY CAUSE LIVER/KIDNEY DAMAGE.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

First Aid:SKIN: WASH W/SOAP & WATER. EYES: FLUSH W/WATER FOR AT LEAST
    15 MIN. GET MD ATTEN. INHAL: REMOVE VICTIM FROM EXPOSURE. IF VICTIM
    IS UNCONSCIOUS GIVE ARTIFICIAL RESPIRATION OR OXYGEN AS NEEDED. GET
    MD A TTEN. INGEST: DO NOT INDUCE VOMITING (ASPIRATION HAZARD). GET
    MD ATTENTION.

=====================  Fire Fighting Measures  =====================

Flash Point Method:CC
Flash Point:98.0F,36.7C
Lower Limits:1.1
Upper Limits:6.1
Extinguishing Media:WATER SPRAY, FOAM, DRY CHEMICAL, OR CO*2.
Fire Fighting Procedures:FIRE FIGHTERS EXPOSED TO VAPORS OR PROD OF
    COMBUSTION SHOULD WEAR NIOSH/MSHA APPPOVED SCBA & FULL PROTECTIVE
    EQUIPMENT .
Unusual Fire/Explosion Hazard:AT ELEVATED TEMPS SUCH AS IN A FIRE,
    POLYMERIZATION MAY TAKE PLACE. IF CONTAINED, VIOLENT RUPTURE MAY
    RESULT.

==================  Accidental Release Measures  ==================

Spill Release Procedures:REMOVE SOURCES OF IGNITION. ABSORB SPILL WITH
    ABSORBENT MATERIAL SUCH AS VERMICULITE OR SAND.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:AVOID STORAGE ABOVE 100F. STORE ONLY
    IN ORIGINAL CONTAINERS.
Other Precautions:STYRENE IS SUBJECT TO REQUIREMENTS OF SARA TITLE III,
    SEC 313; AND 40 CFR 372.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NIOSH/MSHA APPROVED CANISTER TYPE RESPIRATOR
    MUST BE WORN TO PREVENT INHAL OF VAPORS OR SPRAY MISTS WHEN TLV OR
    PEL IS EXCEEDED. WEAR APPROVED DUST MASK WHEN SANDING CURED
    PRODUCT.
Ventilation:GENERAL (MECH) VENTILATION IS REQUIRED DURING NORMAL USE.
Protective Gloves:PLASTIC/CHEMICAL RESISTANT GLOVES.
Eye Protection:CHEM WORK GOG & FULL LENGTH FSHLD.
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:295F,146C
Vapor Pres:4.3
Vapor Density:HVR/AIR
Spec Gravity:1.8
Evaporation Rate &amp; Reference:SLOWER (BUTYL ACETATE=1)
Solubility in Water:NIL
Appearance and Odor:PASTE, SHARP AROMATIC ODOR.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
HEAT & DIRECT SUNLIGHT.
Stability Condition to Avoid:STRONG ACIDS & OXIDIZING AGENTS
Hazardous Decomposition Products:HEATING TO DECOMP MAY CAUSE THE
    EMISSION OF IRRITATING ACRID FUMES.
Conditions to Avoid Polymerization:AT ELEVATED TEMPS (FIRE)
    POLYMERIZATION MAY TAKE PLACE.

====================  Disposal Considerations  ====================

Waste Disposal Methods:SMALL QUANTITIES CAN BE REACTED WITH APPROPRIATE
    HARDENER TO SOLIDIFY. DISPOSE IN ACCORDANCE WITH ALL FEDERAL, STATE
    AND LOCAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.